Zero Torque is a putter technology that keeps the head from naturally rotating open or closed during the stroke. Because the shaft axis runs through the head’s centre of gravity and the putter is balanced at its lie angle, the face stays square to the target more naturally – so you don’t have to “manage” the face with your hands.
Since L.A.B. Golf popularised Lie Angle Balance, more and more brands have launched zero torque putters. This article explains how the technology works, how it differs from traditional face-balanced and toe-hang putters, who it suits, and the zero torque models available at LionGolf.
What is torque in a putter?
In most traditional putters, the head’s centre of gravity (CG) sits away from the shaft axis. When you push the club, the force goes through the shaft while the CG “lags behind”, creating torque around the shaft axis. As a result, the head always tends to rotate on its own – opening on the backstroke and closing on the through-stroke – and the golfer has to compensate with the hands and wrists.
A face that is just 1–2 degrees off at impact noticeably changes the start line of the ball over a few metres. That is why a face that “stays square by itself” matters so much for putting consistency.
How does a Zero Torque putter work?
A zero torque putter is designed so that the (extended) shaft axis passes through the head’s centre of gravity, and the club is balanced at its lie angle in the address position – not with the shaft lying horizontal. Your stroke force and the head’s inertia then act along the same axis, so the head has almost no tendency to rotate.
Brands achieve this in different ways:
- Lie Angle Balance (L.A.B. Golf): every putter is balanced for its lie angle, length, head weight, shaft and grip – so the face always “wants” to stay square.
- Reverse-offset hosel / shaft aligned with the CG (Evnroll ZERO): a reverse-offset hosel lines the shaft axis up with the CG, combined with a high-MOI mallet head.
- Rear-set hosel, toe-up head (Toulon Golf Formula): the shaft is set back while the CG is pushed far forward. Formula [90] is a zero torque design; Formula [45] is near zero torque and keeps some natural arc.
- Principal axis aligned with the stroke (Breakthrough Golf Paradox): a low heel and high toe align the head’s Principal Axis with the stroke, paired with the Stability Tour shaft.
Zero Torque vs Face-Balanced vs Toe-Hang
| Balance type | How to recognise it | Face behaviour | Best for |
|---|---|---|---|
| Toe-hang | Balance the shaft horizontally on a finger – the toe points down | Opens and closes a lot along the arc | Strokes with a clear arc |
| Face-balanced | Balance the shaft horizontally – the face points to the sky | Rotates less, but is only balanced with the shaft horizontal | Straight-back-straight-through or slight-arc strokes |
| Zero Torque / Lie Angle Balance | Hold it at the lie angle – the face points at the target by itself | Almost no self-rotation throughout the stroke | Golfers who want fewer hand manipulations and a consistent start line |
The key difference: a face-balanced putter is only “balanced” with the shaft horizontal – a position nobody putts from. A zero torque putter is balanced in the actual hitting position.
Who should use a Zero Torque putter?
- Golfers who push or pull putts even with correct aim – a sign the face isn’t square at impact.
- Golfers who use a lot of wrist or get “twitchy” on short putts and want a simpler stroke with fewer variables.
- Beginners who want to build a consistent putting stroke from the start.
- Golfers who love a blade shape but want the “no-twist” feel – consider a zero torque blade such as the L.A.B. LINK or Evnroll ZERO Z2s.
Note: zero torque reduces the head’s tendency to rotate, but it does not fix your stroke path or your green reading. Many zero torque models have a different grip position, shaft lean and feel from traditional putters, so a few practice sessions are usually needed to adapt.
Why get fitted for a Zero Torque putter?
Zero torque only works as intended when the putter is balanced for your own setup. The wrong length, lie, shaft lean or loft can cancel out the benefits of the design. On L.A.B. Golf Custom models, length and lie are calculated from each golfer’s stroke.
At LionGolf, our fitters can capture your putting data, compare a zero torque putter with the one you use now and recommend the right configuration. Learn more about our Club fitting service.
Putter grips for Zero Torque
Zero torque putters often come with a forward-leaning shaft, so a traditional grip can make your hands feel unnatural. The SuperStroke Zenergy TLT Off-Axis grip is designed specifically for zero-torque, lie-angle-balanced putters.
Zero Torque putters available at LionGolf
L.A.B. Golf – Lie Angle Balance
LionGolf is the exclusive distributor of L.A.B. Golf in Vietnam. Every L.A.B. putter is lie angle balanced – from the DF3 and OZ.1 mallets to the LINK blade.
Evnroll ZERO Torque
The Evnroll ZERO range combines a reverse-offset hosel for zero torque performance with Evnroll’s grooved face, in mallet, Hatchback and blade shapes.
Toulon Golf Formula
The Toulon Golf Formula range uses multi-material construction to push the CG far forward, with a rear-set hosel and three alignment lines. Choose [90] if you want as little arc as possible, or [45] if you want to keep some natural arc.
![Toulon Golf Formula [90]](https://liongolf.vn/wp-content/uploads/2026/10/toulon-formula-90-1-300x300.webp)
![Toulon Golf Formula [45]](https://liongolf.vn/wp-content/uploads/2026/10/toulon-formula-45-1-300x300.webp)
Breakthrough Golf Paradox
Breakthrough Golf Paradox comes in Mallet and Blade shapes, designed so the head’s principal axis aligns with the stroke; the Paradox Tour version comes with the Stability Tour shaft and adjustable loft / lie.
Matching accessories
Frequently asked questions
Will a zero torque putter help me hole more putts?
No putter can guarantee that. Zero torque keeps the face more stable, so your start line becomes more consistent – but results still depend on your stroke, green reading and speed control.
Can golfers with an arc stroke use a zero torque putter?
Yes, but it will feel different: the head won’t rotate along the arc the way a toe-hang putter does. If you want to keep some arc, consider a near zero torque design such as the Toulon Golf Formula [45]. Try it in person and get fitted before deciding.
Can I fit a standard grip on a zero torque putter?
You can, but many models are optimised for an off-axis grip or the manufacturer’s own grip. Ask LionGolf before changing it so the putter’s balance isn’t affected.
Where can I try a zero torque putter?
Visit a LionGolf store in Ho Chi Minh City or call our customer hotline 0967 543 542 for advice and to book a fitting.
